3500/72M 1.本特利bently3500对机组的振动监测状态监测测点配置要求
键相：压缩机组的每个相同转速的轴系配置一个键相位测点；采用本特利3300XL系列电涡流传感器进行测量。
轴振：每个滑动支持轴承上配置一对X/Y方向（互为垂直安装）的轴振测点，采用本特利3300XL系列电涡流传感器进行测量。
轴位移：压缩机组的每个推力轴承处配置双冗余的轴向位移测点；采用本特利3300XL系列电涡流传感器进行测量。
瓦振：每个滚动支持轴承上配置两个瓦振测点（水平和垂直方向安装），采用本特利330500系列Velomitor压电式振动速度传感器进行测量。
轴承温度（如适用）：每个滑动支持轴承及推力轴承均配置轴瓦温度测点；推力轴承的工作面和非工作面应同时配置温度测点。
齿轮箱壳振（如适用）：每个齿轮箱的输入和输出轴的支持轴承处各配置一对X/Y方向壳振测点；采用本特利330400系列压电式振动加速度传感器进行测量。
2.本特利bently3500配置要求
每套关键压缩机组配备的本特利3500框架
每个本特利3500框架内配置冗余的3500/15电源模块
每个本特利3500框架内配置3500/22M瞬态数据接口模块；
针对上述键相测点，每套机组的本特利3500框架内配置相应的3500/25键相模块
针对上述轴振、轴位移、瓦振、及壳振测点，均须配置相应的3500/42M监测器模块
（如适用），上述轴承温度测点，需配置相应的3500/60、61温度监测模块，或3500/62过程量监测模块
每个监测通道（轴振、轴位移和瓦振）配置D立的两个继电器输出通道；采用3500/32（4通道）或3500/33（16通道）继电器模块
每个本特利3500框架内配置一个3500/92Modbus通讯网关
对于工作在危险区的机组，接入现场信号的3500监测器模块要带有内置安全栅；并且3500框架内要配置3500/04本安接地模块。
螺杆压缩机
对于工作在危险区域的机组，本特利传感器及监测系统都要带有多机构批准单位选项。而对于工作在安全区的机组，则不做要求。
1.本特利bently测点配置要求
键相：压缩机组的每个相同转速的轴系配置一个键相位测点；采用本特利3300XL系列电涡流传感器进行测量。
轴振：每个滑动支持轴承上配置一对X/Y方向（互为垂直安装）的轴振测点，采用本特利3300XL系列电涡流传感器进行测量。
轴位移：压缩机组的每个推力轴承处配置双冗余的轴向位移测点；采用本特利3300XL系列电涡流传感器进行测量。
瓦振：每个滚动支持轴承上配置两个瓦振测点（水平和垂直方向安装），采用本特利330500系列Velomitor压电式振动速度传感器进行测量。
轴承温度（如适用）：每个滑动支持轴承及推力轴承均配置轴瓦温度测点；推力轴承的工作面和非工作面应同时配置温度测点。
齿轮箱壳振（如适用）：每个齿轮箱的输入和输出轴的支持轴承处各配置一对X/Y方向壳振测点；采用本特利330400系列压电式振动加速度传感器进行测量。
2.3500配置要求
每套关键压缩机组配备本特利3500框架
每个本特利3500框架内配置冗余的3500/15电源模块
每个本特利3500框架内配置3500/22M瞬态数据接口模块（RJ45网络接口）
针对上述键相测点，每套机组的本特利3500框架内配置相应的3500/25键相模块
针对上述轴振、轴位移、瓦振、及壳振测点，均须配置相应的3500/42M监测器模块
（如适用），上述轴承温度测点，需配置相应的3500/60、61温度监测模块，或3500/62过程量监测模块
每个监测通道（轴振、轴位移和瓦振）配置D立的两个继电器输出通道；采用3500/32（4通道）或3500/33（16通道）继电器模块
每个本特利3500框架内配置一个3500/92Modbus通讯网关
对于工作在危险区的机组，接入现场信号的3500监测器模块要带有内置安全栅；并且3500框架内要配置3500/04本安接地模块。API618往复式压缩机
对于工作在危险区域的机组，本特利传感器及监测系统都要带有多机构批准单位选项。而对于工作在安全区的机组，则不做要求。
1.测点配置要求
多事件键相：往复式压缩机的驱动端安装多事件键相转轮MEW来测量往复式压缩机的键相参考信号。该多事件键相转轮可选择本特利标准多事件转轮MEW，或者往复式压缩机生产厂家结合自己设备结构设计特点、按照本特利对于多事件键相转轮的工程实践经验来特殊定制和设计多事件键相转轮。多事件键相信号采用本特利3300XL系列电涡流传感器进行测量。
曲轴箱振动：在往复式压缩机曲轴箱两个气缸列之间的每个主轴承的水平轴线上配置一个振动速度传感器测量曲轴箱体振动。当往复式压缩机的工作转速高于500rpm时采用本特利330500系列Velomitor压电式振动速度传感器；当工作转速低于500rpm时采用本特利190501VelomitorCT压电式振动速度传感器。
十字头振动：在往复式压缩机每个气缸十字头运动中点位置的垂直平面上配置冗余的加速度传感器来监测往复运动部件的冲击事件；采用本特利330425加速度传感器进行测量。
活塞杆位置：在往复式压缩机每个气缸垂直于活塞杆平面的水平和垂直方向，配置一对互为垂直的活塞杆位置测点；采用本特利3300XL系列电涡流传感器进行测量。对于往复式压缩活塞杆的测量。
气缸动态压力：在往复式压缩机的每个气缸上配置两个气缸压力测点（吸气和排气），采用本特利165855气缸压力传感器进行测量。
轴承振动：往复式压缩机曲轴箱中每个主轴承配置一个速度传感器测量轴承的振动。当往复式压缩机的工作转速高于500rpm时采用本特利330500系列Velomitor压电式振动速度传感器；当工作转速低于500rpm时采用本特利190501VelomitorCT压电式振动速度传感器。
轴承温度：每个主轴承上配置温度传感器测量轴承温度。
气阀温度：在往复式压缩机气缸的每个气阀（吸气阀和排气阀）上配置温度测量阀门温度。
齿轮箱壳振（如适用）：每个齿轮箱的输入和输出轴的支持轴承处各配置一对X/Y方向壳振测点；采用本特利330400系列压电式振动加速度传感器进行测量。
电动机瓦振：每个滚动支持轴承上配置两个瓦振测点（水平和垂直方向安装），采用本特利330500系列Velomitor压电式振动速度传感器进行测量。
For units working in hazardous areas, Bentley sensors and monitoring systems should have the option of multi agency approval units. There is no requirement for the units working in the safe area.
1. Bently 3500's requirements on the configuration of measuring points for vibration monitoring of the unit
Keyphasor: each shafting of the compressor unit at the same speed is equipped with a Keyphasor measuring point; Bentley 3300XL series eddy current sensor is used for measurement.
Shaft vibration: each sliding support bearing is equipped with a pair of shaft vibration measuring points in X/Y direction (installed vertically to each other), which are measured by Bentley 3300XL series eddy current sensors.
Axial displacement: each thrust bearing of the compressor unit is equipped with double redundant axial displacement measuring points; Bentley 3300XL series eddy current sensor is used for measurement.
Bearing vibration: each rolling support bearing is equipped with two bearing vibration measuring points (installed horizontally and vertically), which are measured by Bentley 330500 series Velomitor piezoelectric vibration velocity sensor.
Bearing temperature (if applicable): each sliding support bearing and thrust bearing shall be equipped with bearing pad temperature measuring points; The working face and non working face of thrust bearing shall be equipped with temperature measuring points at the same time.
Gearbox shell vibration (if applicable): a pair of X/Y direction shell vibration measuring points shall be provided at the support bearings of input and output shafts of each gearbox; Bentley 330400 series piezoelectric vibration acceleration sensor is used for measurement.
2. Bently 3500 configuration requirements
Bently 3500 frame for each key compressor unit
Each Bently 3500 rack is configured with redundant 3500/15 power modules
3500/22M transient data interface module is configured in each Bentley 3500 rack;
For the above Keyphasor measurement points, the Bently 3500 rack of each unit is equipped with corresponding 3500/25 Keyphasor modules
The 3500/42M monitor module must be configured for the above measuring points of shaft vibration, shaft displacement, bearing vibration and shell vibration
(If applicable), the above bearing temperature measuring points need to be configured with corresponding 3500/60, 61 temperature monitoring modules, or 3500/62 process quantity monitoring modules
Each monitoring channel (shaft vibration, shaft displacement and bearing vibration) is equipped with two relay output channels of D-type; Use 3500/32 (4-channel) or 3500/33 (16 channel) relay modules
Each Bently 3500 rack is configured with a 3500/92Modbus communication gateway
For units working in hazardous areas, 3500 monitor modules connected to field signals shall be equipped with built-in safety barriers; 3500/04 intrinsically safe grounding module shall be configured in the 3500 rack.
screw compressor
For units working in hazardous areas, Bentley sensors and monitoring systems should have the option of multi agency approval units. There is no requirement for the units working in the safe area.
1. Bently measuring point configuration requirements
Keyphasor: each shafting of the compressor unit at the same speed is equipped with a Keyphasor measuring point; Bentley 3300XL series eddy current sensor is used for measurement.
Shaft vibration: each sliding support bearing is equipped with a pair of shaft vibration measuring points in X/Y direction (installed vertically to each other), which are measured by Bentley 3300XL series eddy current sensors.
Axial displacement: each thrust bearing of the compressor unit is equipped with double redundant axial displacement measuring points; Bentley 3300XL series eddy current sensor is used for measurement.
Bearing vibration: each rolling support bearing is equipped with two bearing vibration measuring points (installed horizontally and vertically), which are measured by Bentley 330500 series Velomitor piezoelectric vibration velocity sensor.
Bearing temperature (if applicable): each sliding support bearing and thrust bearing shall be equipped with bearing pad temperature measuring points; The working face and non working face of thrust bearing shall be equipped with temperature measuring points at the same time.
Gearbox shell vibration (if applicable): a pair of X/Y direction shell vibration measuring points shall be provided at the support bearings of input and output shafts of each gearbox; Bentley 330400 series piezoelectric vibration acceleration sensor is used for measurement.
2.3500 Configuration requirements
Each key compressor unit is equipped with Bentley 3500 frame
Each Bently 3500 rack is configured with redundant 3500/15 power modules
3500/22M Transient Data Interface Module (RJ45 Network Interface) is configured in each Bentley 3500 rack
For the above Keyphasor measurement points, the Bently 3500 rack of each unit is equipped with corresponding 3500/25 Keyphasor modules
The 3500/42M monitor module must be configured for the above measuring points of shaft vibration, shaft displacement, bearing vibration and shell vibration
(If applicable), the above bearing temperature measuring points need to be configured with corresponding 3500/60, 61 temperature monitoring modules, or 3500/62 process quantity monitoring modules
Each monitoring channel (shaft vibration, shaft displacement and bearing vibration) is equipped with two relay output channels of D-type; Use 3500/32 (4-channel) or 3500/33 (16 channel) relay modules
Each Bently 3500 rack is configured with a 3500/92Modbus communication gateway
For units working in hazardous areas, 3500 monitor modules connected to field signals shall be equipped with built-in safety barriers; 3500/04 intrinsically safe grounding module shall be configured in the 3500 rack. API618 reciprocating compressor
For units working in hazardous areas, Bentley sensors and monitoring systems should have the option of multi agency approval units. There is no requirement for the units working in the safe area.
1. Requirements for measuring point configuration
Multi event Keyphasor: A multi event Keyphasor runner MEW is installed at the drive end of the reciprocating compressor to measure the Keyphasor reference signal of the reciprocating compressor. The multi event Keyphasor runner can be Bentley standard multi event runner MEW, or the reciprocating compressor manufacturer can customize and design the multi event Keyphasor runner according to Bentley's engineering experience in multi event Keyphasor runner based on its own equipment structure design characteristics. The multi event Keyphasor signal is measured by Bentley 3300XL series eddy current sensor.
Crankcase vibration: a vibration speed sensor is arranged on the horizontal axis of each main bearing between two cylinder rows of the reciprocating compressor crankcase to measure the crankcase body vibration. Bentley 330500 series Velomitor piezoelectric vibration speed sensor is used when the working speed of the reciprocating compressor is higher than 500 rpm; Bentley 190501VelomitorCT piezoelectric vibration speed sensor is used when the working speed is lower than 500rpm.
Crosshead vibration: redundant acceleration sensors are configured on the vertical plane at the midpoint of crosshead movement of each cylinder of the reciprocating compressor to monitor the impact event of reciprocating components; Bentley 330425 acceleration sensor is used for measurement.
Piston rod position: a pair of mutually perpendicular piston rod position measuring points shall be configured in the horizontal and vertical directions of each cylinder of the reciprocating compressor perpendicular to the piston rod plane; Bentley 3300XL series eddy current sensor is used for measurement. For reciprocating compression piston rod measurement.
Cylinder dynamic pressure: each cylinder of the reciprocating compressor is equipped with two cylinder pressure measuring points (suction and exhaust), which are measured by Bentley 165855 cylinder pressure sensor.
Bearing vibration: each main bearing in the crankcase of the reciprocating compressor is equipped with a speed sensor to measure the bearing vibration. Bentley 330500 series Velomitor piezoelectric vibration speed sensor is used when the working speed of the reciprocating compressor is higher than 500 rpm; Bentley 190501VelomitorCT piezoelectric vibration speed sensor is used when the working speed is lower than 500rpm.
Bearing temperature: each main bearing is equipped with a temperature sensor to measure the bearing temperature.
Air valve temperature: each air valve (suction valve and exhaust valve) of the reciprocating compressor cylinder is equipped with a temperature measuring valve temperature.
Gearbox shell vibration (if applicable): a pair of X/Y direction shell vibration measuring points shall be provided at the support bearings of input and output shafts of each gearbox; Bentley 330400 series piezoelectric vibration acceleration sensor is used for measurement.
Motor pad vibration: each rolling support bearing is equipped with two pad vibration measuring points (installed horizontally and vertically), which are measured by Bentley 330500 series Velomitor piezoelectric vibration velocity sensor.
| BENTLY | 3500/22M-01-01-01 | |
| BENTLY | 3500/22M 288055-01 | |
| BENTLY | 3500/22M | |
| BENTLY | 1900/65A | |
| BENTLY | 1900/65A-01-01-01-00-00 | |
| BENTLY | 3500/53 | |
| BENTLY | 3500/70M | |
| BENTLY | 3500/15 | |
| BENTLY | 3500/42M | |
| BENTLY | 133819-02 | |
| BENTLY | 3500/60 | |
| BENTLY | 3500/72M | |
| BENTLY | 3500/40M（140734-01） | |
| BENTLY | 135473-01 | |
| BENTLY | 3500/20 | |
| BENTLY | 3500/61 | |
| BENTLY | 135489-04 | |
| BENTLY | 3300/16-11-01-03-00-00-01 | |
| BENTLY | 330130-045-00-00 | |
| BENTLY | 1900/55 | |
| BENTLY | 3500/92 | |
| BENTLY | 3300/20-12-01-03-00-00 | |
| BENTLY | 3500/05-01-01-00-00-01 | |
| BENTLY | 1900/27 | |
| BENTLY | 167699-02 | |
| BENTLY | 133396-01 | |
| BENTLY | 3500/15 127610-01 | |
| BENTLY | 125760-01 | |
| BENTLY | 3500/25 | |
| BENTLY | 146031-02 | |
| BENTLY | 133323-01 | |
| BENTLY | 146031-01 | |
| BENTLY | 9200-01-01-10-00 | |
| BENTLY | 3500/45 | |
| BENTLY | 3500/34 | |
| BENTLY | 135613-02 | |
| BENTLY | 60M100-00 | |
| BENTLY | 84152-01 | |
| BENTLY | 136719-01 | |
| BENTLY | 125680-01 | |
| BENTLY | 125720-01 | |
| BENTLY | 140471-01 | |
| MECS | UTV-F2500HA | |
| MECS | CS-1000 | |
| MECS | UTX1010 | |
| MECS | CPU-1000 | |
| REXROTH | RAC2.2-200-460-A00-W1 | |
| REXROTH | MDD112D-N030-N2M-130GA0 | |
| REXROTH | TV3000HTPUMF | |
| REXROTH | DKC02.3-200-7-FW | |
| REXROTH | MHD093C-058-PG1-AA | |
| REXROTH | R901325866+R900775346+R901273425A | |
| REXROTH | HDS03.2-W075N-HS12-01-FW | |
| REXROTH | 0360-500-00/MF01 | |
| REXROTH | CSB01.1N-AN-ENS-NNN-NN-S-NN-FW | |
| REXROTH | DKC03.3-040-7-FW | |
| REXROTH | MSK070C-0150-NN-S1-UG0-NNNN | |
| REXROTH | MSK070D-0450-NN-M1-UP1-NSNN | |
| REXROTH | VDP40.2BIN-G4-PS-NN | |
| REXROTH | 0608820116 | |
| REXROTH | DKC10.3-012-3-MGP-01VRS | |
| REXROTH | MSK060C-0600-NN-M1-UP1-NSNN | |
| KROHNE | KDB-FT1600 | |
| KROHNE | Q75T100S | ASSY78462-01U 9200-06-02-10-00 84152-01 60M100-00 3500/92 136180-01 3500/72M 3500/62-04-02 3500/70M 3500/62-04-02 3500/61 3500/60 163179-01 3500/53 133388-01 3500/45 176449-04 3500/44M 176449-03 3500/42M 140734-02 3500/40M（140734-01） 3500/40M 176449-01 3500/40M 140734-01 3500/34 3500/33 149986-01 3500/32 125712-01 3500/25 184684-01 3500/22M 138607-01 3500/20 125744-02 3500/15 133292-01 3500/15 106M1079-01 3500/15 127610-01 3500/05-01-03-00-00-00 3500/05-01-01-00-00-01 330980-51-00 330901-05-32-05-02-00 330703-000-070-10-02-05 ASSY78462-01U 9200-06-02-10-00 84152-01 60M100-00 3500/92 136180-01 3500/72M 3500/62-04-02 3500/70M 3500/62-04-02 3500/61 3500/60 163179-01 3500/53 133388-01 3500/45 176449-04 3500/44M 176449-03 3500/42M 140734-02 3500/40M（140734-01） 3500/40M 176449-01 3500/40M 140734-01 3500/34 3500/33 149986-01 3500/32 125712-01 3500/25 184684-01 3500/22M 138607-01 3500/20 125744-02 3500/15 133292-01 3500/15 106M1079-01 3500/15 127610-01 3500/05-01-03-00-00-00 3500/05-01-01-00-00-01 330980-51-00 330901-05-32-05-02-00 330703-000-070-10-02-05 ASSY78462-01U 9200-06-02-10-00 84152-01 60M100-00 3500/92 136180-01 3500/72M 3500/62-04-02 3500/70M 3500/62-04-02 3500/61 3500/60 163179-01 3500/53 133388-01 3500/45 176449-04 3500/44M 176449-03 3500/42M 140734-02 3500/40M（140734-01） 3500/40M 176449-01 3500/40M 140734-01 3500/34 3500/33 149986-01 3500/32 125712-01 3500/25 184684-01 3500/22M 138607-01 3500/20 125744-02 3500/15 133292-01 3500/15 106M1079-01 3500/15 127610-01 3500/05-01-03-00-00-00 3500/05-01-01-00-00-01 330980-51-00 330901-05-32-05-02-00 330703-000-070-10-02-05 |
微信二维码