Frequently Asked Questions about DS200PCCAG10ACB
What does DS200PCCAG10ACB do for lower horsepower controllers?
For low-to-medium horsepower controllers, DS200PCCAG10ACB includes snubber circuits to control spikes across the AC lines, DC bus, and gate drivesr. For higher horsepower controllers, some or all of the snubber circuits are omitted from the DS200PCCAG10ACB board.
How many jumpers does DS200PCCAG10ACB have?
DS200PCCAG10ACB has four wire jumpers. DS20

SCXI -1346（部件号：776574-46）适用于涉及多机箱 SCXI 的应用，因为它可以将它们连接到一个 DAQ 设备。此电缆适配器有两个电缆连接。一个连接用于来自数字化仪或以前的 SCXI 机箱的信号，而第二个连接用于将数字化仪的信号路由到后续机箱。SH68-68 -EP（部件号：184749-01，1 m 电缆；184749-02，2 m 电缆；184749-05，5 m 电缆；或184749-10，10 m 电缆）可单独购买并与NI SCXI 1346。这个电缆适配器有一个安装支架，可以可靠地连接到 SCXI 底盘。

SCXI 1346有四个连接器。个连接器是前面板上的 68 针公连接器，上面印有 To Next Chassis。下一个连接器是前面板上的另一个 68 针公连接器，上面印有 From DAQ Board 或 Previous Chassis。第三个连接器是印刷电路板上的 50 针公分线连接器。后一个连接器也是 50 针连接器，但它是电缆适配器背面的支架安装母头。

使用NI SCXI 1346在多机箱系统中，需要以下物品：一台计算机、一把小平头螺丝刀、68 针屏蔽电缆、一个 68 针 E 系列 DAQ 设备、一个 SCXI 1001 或 SCXI 1000 机箱（版本 K 或更高版本）、一个每个机箱的或更多 SCXI 模块（SCXI-1127、SCXI-1190 和 SCXI-1191 除外）、SCXI 1349 屏蔽电缆组件和 SCXI-1346 安装指南。用户应牢记在多机箱 SCXI 系统中使用的总电缆长度不要超过 10 m。这将有助于确保可靠的操作。

SCXI 1346使用与软件包/应用程序开发环境 (ADE) 兼容的 NI-DAQmx 驱动软件运行，例如 LabVIEW、LabWindows、LabVIEW SignalExpress、Measurement Studiio、Visual C++ 或 Visual Basic。可以使用 National Instruments Measurement & Automation Explorer (MAX) 工具配置设备硬件。
SCXI - 1346 (part number: 776574-46) is suitable for applications involving multiple chassis SCXI, because it can connect them to a DAQ device. This cable adapter has two cable connections. One connection is used for the signal from the digitizer or the previous SCXI chassis, while the second connection is used to route the signal from the digitizer to the subsequent chassis. SH68-68 - EP (Part No.: 184749-01, 1 m cable; 184749-02, 2 m cable; 184749-05, 5 m cable; or 184749-10, 10 m cable) can be purchased separately and with NI SCXI 1346. This cable adapter has a mounting bracket that can be reliably connected to the SCXI chassis.



The SCXI 1346 has four connectors. The first connector is the 68-pin male connector on the front panel, which is printed with To Next Chassis. The next connector is another 68-pin male connector on the front panel, which is printed with From DAQ Board or Previous Chassis. The third connector is the 50-pin centimeter connector on the printed circuit board. The last connector is also a 50-pin connector, but it is the bracket mounting female on the back of the cable adapter.



Using NI SCXI 1346 in a multi-chassle system requires the following items: a computer, a small flat-head screwdriver, a 68-pin shielded cable, a 68-pin E-series DAQ device, a SCXI 1001 or SCXI 1000 chassis (version K or later), one or more SCXI modules per chassis (excluding SCXI-1127, SCXI-1190 and SCXI-1191), SCXI 1349 shielded cable assembly, and SCXI-1346 installation guide. Users should keep in mind that the total cable length used in the multi-case SCXI system should not exceed 10 m. This will help ensure reliable operation.



SCXI 1346 runs with NI-DAQmx driver software compatible with the package/application development environment (ADE), such as LabVIEW, LabWindows, LabVIEW SignalExpress, Measurement Studio, Visual C++, or Visual Basic. You can use the National Instruments Measurement&Automation Explorer (MAX) tool to configure the device hardware.